| Powered Roller Conveyors |
| |
| Powered Roller conveyors the effective solution for transporting unit loads. |
| |
| For packages as small as 250mm in length. Handles packages up to 30kg at speeds of up to 30m/min. |
| |
| |
| | | | Straight | | | | These modules are supplied as a driving straight or slave straight With the stave slraght being the most commonly used of all the modules, when using a Lineshanl Conveyor System. | | |  | Slave and driving straights available |
| | Modules up to 3 metres in length |
| | 83mm, 125mm and 167mm roller pitch |
| | |
|
|
To receive more information about Straight Powered Roller Conveyors, please click here. |
| |
| |
| |
| | | | Zero Line Pressure (ZLP) Straight | | | | Zero line Pressure accumulation will effectively queue loads without contact in a series of de-energised zones until the way ahead is clear and the loads can safety proceed. Each zone comes complete with its own intelligent optopneumatic sensor and valve. Multiple ZLP zones simply plug together for immediate operation. | | | | Standard ZIP Straights range from two to four 750mm ZLP zones |
| | 1.5m to 3m modules |
| | Accumulate with no load contact at up to 30 m/min |
| | |
|
|
To receive more information about Zero Line Pressure (ZLP) Straight, please click here. |
| |
| |
| | | | Drive Unit | | | | Drive units are fitted to driving straights which are the same as slave straights but with a chain sprocket attached to the driveshaft. Straights fitted with a drive unit can drive up to 40 metres at 83mm pitch, 60 metres at 125mm pitch and 80 metres at 157mm pitch of straight conveyor. | | | | Full range of widths |
| | Speeds 9, 14, 18, 24 and 30m/min |
| | Can drive up to 80 metres of conveyor |
| | |
|
|
To receive more information about Drive Unit Powered Roller Conveyors, please click here. |
| |
| |
| | | | Personnel Gate | | | | The personnel gate utilises a very simple and effective spring loaded coupling system which picks up drive from the adjacent module. Drive is lost when the gate a lifted. Gas struts give assistance during lifting and closing of the gate. | | | | Available in all standard widths (300 - 800 BB) |
| | Available in 1000mm modulus for 805mm clear entry |
| | Left and Right handed units available |
| | |
|
|
To receive more information about Personnel Gate Powered Roller Conveyors, please click here. |
| |
| |
| | | | Spur | | | | Spurs come assembled with 2 metre or 2.5 metre straights and are used where one conveyor feeds into another. The loads are merged into the main tine conveyor at an angle of 30 degrees. | | | | Spurs - come in two types |
| | 1. | Where module incorporates a crossdrive from straight to spur rollers |
| | 2. | Where spur section rollers are powered from an adjacent conveyor line |
| | Available in alt standard widths (300 - 800 GB) |
| | Available with or without crossdrive |
| | |
|
|
To receive more information about LVP Spur Powered Roller Conveyors, please click here. |
| |
| |
| | | | Curves | | | | Rollers are tapered and multi-grooved to facilitate the driving bells and jump belts. Each drive shaft is connected by flexible precision universal joints, fitted with needle roller bearings for smooth quiet running, governed by the length of belt itself | | | | Full range of widths |
| | 30, 45, 60 and 90 curves |
| | Tapered rollers |
| | |
|
|
To receive more information about Curves Powered Roller Conveyors, please click here. |
| |
| |
| | | | Corner Turn | | | | The corner turn module allows a 90° change of direction in a space of 600mm or 900mm square; the outside rollers rotate faster than the inside rollers, to help drive the packages through the turn. Two modules may be assembled together where a 180° turn is required. A 600mm square corner him is used for conveyors having back to back sizes of 300, 400, 450 and 500mm. A 900mm square corner turn is used for conveyors 600mm and 600mm, square back to back | | | | Full range of widths |
| | 90 and 150 degree corner turns |
| | Available in 600mm˛ and 900mm˛ |
| | |
|
|
To receive more information about Corner Turn Powered Roller Conveyors, please click here. |
| |
| | | | Belt driven roller | | | | Belt driven roller conveyors are for the horizontal transportation of items and assembly line operations. They are available in lengths from 2m up to 30m in 0.5m increments. They are constructed using cold formed steel and powder coated channels with two bed type options - Live Roller and Accumaflow. | | | | Centre Driven belt speeds 9, 14, 18, 24 and 30m per minute. |
| | End Driven by a motorised drum, belt Speeds - 15.6, 18.6 and 21.6m per minute |
| | Robust and durable 2-ply transmission belt. |
| | |
|
|
To receive more information about the Light Duty Belt Driven Roller, please click here. |
| |
